Kenmore dryer parts replacement

Dryers wear out in a pattern. A belt snaps, a fuse blows, an element opens or a latch breaks. This guide lists the Kenmore dryer parts we replace, what the fault looks like and when to call. Unplug the dryer before you look inside. The right part depends on the model number, so find your model number first. We test the part before we call it bad. If you would rather not replace the part yourself, our dryer repair in Kenmore, WA service can do it for you.

Heat and temperature parts

Heating element and coil replacement

The dryer runs and the drum turns, but the clothes stay damp. On an electric dryer the heating element or coil may be open. We test it with a meter before we replace it. This covers Kenmore dryer heating element replacement, Kenmore Elite heating elements and element replacement on 70, 80, 90 and 110 series dryers.

Thermal fuse and thermostat replacement

A blown thermal fuse can stop the heat or stop the dryer from starting. It blows for a reason, usually a blocked vent. We clear the cause, then replace the fuse. A worn thermostat can also cause no heat or too much heat.

Gas dryer igniter, coil, gas valve and pilot light

On a gas dryer, no heat can come from the igniter, the gas valve coils or the gas valve. Older gas dryers had a pilot light. Gas parts are for a technician. If you smell gas, leave the home and call 911 or your gas utility.

Drive and drum parts

Belt replacement

A snapped belt means the motor hums but the drum does not turn. A squeal or thump can mean the belt is worn. Kenmore dryer belt replacement covers the drive belt, drum belt and band on front load, gas, electric and old models. We replace the belt together with worn pulleys and rollers so it does not fail again.

Idler pulley, motor pulley and drum rollers

A squeaky or squealing dryer often has a worn idler pulley or worn drum rollers, also called wheels. A loose drum points the same way. We replace the worn parts as a set when it makes sense.

Bearing, drum and felt seal replacement

A grinding noise can mean a worn bearing. The felt seal on the front of the drum can wear and make noise or let lint through. A damaged drum is rare, and we tell you if repair is worth it.

Motor replacement

A motor that hums, does not turn or trips the breaker needs a test. Motor replacement costs more than most repairs, so we explain the cost first. See how pricing works.

Blower wheel and fan replacement

A loose or damaged blower wheel gives weak airflow, long dry times or a rattle. We check the wheel when we clear the vent.

Door and latch parts

Door latch, handle and hinge replacement

If the door will not stay closed, the latch or hinge may be worn. A broken handle is common on Kenmore Elite HE3 dryers. The dryer will not start with the door open. We also check the door switch.

Door seal and gasket replacement

A worn door seal or gasket lets warm air and lint escape. You may see lint around the door or smell hot lint. We replace the seal and clean the area.

Controls and sensors

Control board repair and replacement

A control board can fail and show a code such as F01. Switch the dryer off at the breaker for 10 minutes first. If the code returns, the board may need repair or replacement. See the error codes guide.

Start switch and start button replacement

If you press start and nothing happens, the start switch or button may be bad. The door switch and power can cause the same fault. We test each one.

Moisture sensor and other sensors

A Kenmore dryer sensor that is not working can cause damp clothes or a dryer that stops too soon. We check the wiring and test the sensor. We replace it only if it fails.

Power cord replacement

A cracked or burnt power cord is not safe. Unplug the dryer and call us. The cord must match your dryer, gas or electric.

Airflow parts

Lint screen and lint trap replacement

A torn lint screen or lint trap lets lint into the dryer. This covers a Kenmore dryer lint screen replacement and a Kenmore Elite lint screen replacement. Clean the screen after every load.

Dryer vent replacement

A crushed or clogged vent hose causes long dry times and overheating. We can replace the vent hose and clear the duct. See the fire safety guide.

Light bulb replacement

A dead drum light is simple. Unplug the dryer, then fit the right bulb for your model.

Kenmore dryer repair kits

Are repair kits worth it?

A Kenmore dryer repair kit usually groups wear parts, such as a belt, idler pulley and rollers. A kit helps only when those parts are worn. We test first, so you do not pay for parts that are fine.

How we choose the right replacement part

Kenmore dryer replacement parts change by series and by builder. We look up your model number and match the part, for old Kenmore dryers, Kenmore Elite dryers and gas and electric models. Want to try it yourself? Read our manuals, parts and DIY help guide first, and stop if the job involves gas.

Kenmore dryer parts questions

Which Kenmore dryer part should I replace first?

Test the cheap and common parts first: the vent, the thermal fuse, the belt and the lint screen. The part depends on the fault, so tell us what the dryer is doing.

Can you replace parts on old Kenmore dryers?

Yes. Old Kenmore dryers need the exact model number so we can match the belt, element or fuse.

Is a dryer repair kit worth buying?

Only if the parts in the kit are worn. We test the dryer first so you do not buy parts you do not need.

Do you replace gas dryer parts?

Yes. A gas dryer igniter, coil or valve is for a technician. If you smell gas, leave the home and call your gas utility.